Age verification
Please confirm that you are 18 years or older to enter the shop.
Have patience...
You are not old enough to visit the shop yet.
Products
Viper Tactical Special Ops Lanyard - Sand
Special Ops Lanyard - Sand Made using 25mm nylon webbing Adjustable quick release belt loop. Extends from 55cm to 140cm
£12.95
-
Splatterburst Splatterburst Targets - 1" Self Adhesive - 620 Targets / 10 Sheets
Splatterburst Targets - 1" Self Adhesive Each sheet has 62 adhesive 1" targets, 620 total targets. BRIGHT HIGH CONTRASTING colors make it EASY to see you shots at a distance, no more wasting time walking downrange to SEE YOUR SHOTS. Our new "Stick & Splatter" HIGH STRENGTH adhesive targets stick to almost anything at any temperature. The ULTIMATE TARGET for all firearms and calibers, including; Airsoft, BB, pellet guns and air rifles. Our HIGH VISIBILITY splatter targets make it EASY to see your shots and work flawlessly shooting indoors or outdoors, short range or long range. When peeling and sticking each target we recommend sticking onto a paper 80gsm or above. These are the ones used in the videos made by Giles.
£10.49
-
Splatterburst Splatterburst Targets - 2" Self Adhesive - 400 Targets / 25 Sheets
Splatterburst Targets - 2" Self Adhesive Each sheet has 16 adhesive 2" targets, 400 total targets. BRIGHT HIGH CONTRASTING colors make it EASY to see you shots at a distance, no more wasting time walking downrange to SEE YOUR SHOTS. Our new "Stick & Splatter" HIGH STRENGTH adhesive targets stick to almost anything at any temperature. The ULTIMATE TARGET for all firearms and calibers, including; Airsoft, BB, pellet guns and air rifles. Our HIGH VISIBILITY splatter targets make it EASY to see your shots and work flawlessly shooting indoors or outdoors, short range or long range. When peeling and sticking each target we recommend sticking onto a paper 80gsm or above. These are the ones used in the videos made by Giles.
£14.49
-
Jack Pyke Sporter Knife 3" - Jack Pyke
Sporter Knife 3" - Jack Pyke Steel blade Belt Clip 'Deep forest' handle Complete with nylon pouch Over 18's ONLY Strictly In Store Collection and ID will be required. We DO NOT retail this item outside of the store in the UK. If you attempt to circumnavigate the in store collection policy we will refuse your custom. If you purchase and REFUSE to collect from store, we will deduct any merchant charges that have been applied to us.
£14.99
-
Sportsmatch Sportsmatch - 1 Inch Dovetail 9.5-11.5mm - HT08C - 24mm Mounts
Sportsmatch - 1 Inch Dovetail 9.5-11.5mm - HT08C - 24mm Mounts 1 Inch Diameter Body Tube - High 24mm ( A ) Mounts Tube Diameter = 1 Inch Mount System = 9.5 -11.5 mm dovetail Model HT08C With Arestor Pin HT08C - Sportsmatch Website
£23.99
-
Sportsmatch Sportsmatch - 1 Inch Dovetail 9.5-11.5mm - LT031C - 13mm Mounts
Sportsmatch - 1 Inch Dovetail 9.5-11.5mm - LT031C - 13mm Mounts 1 Inch Diameter Body Tube - Low 13mm ( A ) Mounts Tube Diameter = 1 Inch Mount System = 9.5 -11.5 mm dovetail Model TO31C
£23.49
-
Sportsmatch Sportsmatch - 1 Inch Dovetail 9.5-11.5mm - TO4C - 21mm Mounts
Sportsmatch - 1 Inch Dovetail 9.5-11.5mm - TO4C - 21mm Mounts 1 Inch Diameter Body Tube - Med 21mm ( A ) Mounts Tube Diameter = 1 Inch Mount System = 9.5 -11.5 mm dovetail Model TO4C
£24.42
-
Sportsmatch Sportsmatch - 30mm Dovetail 9.5-11.5mm - Extra High - HT071
Sportsmatch - 30mm Dovetail 9.5-11.5mm - Extra High - HT071 30mm Diameter Body Tube High Range 3/8" Scope Mounts For 11mm dovetails / grooves up to 60mm lens diameter (on most rifles) Tube Diameter = 30mm Mount System = 9.5 -11.5 mm dovetail HT071
£41.99
-
Sportsmatch Sportsmatch - 30mm Dovetail 9.5-11.5mm - HT036C - 21mm Mounts
Sportsmatch - 30mm Dovetail 9.5-11.5mm - HT036C - 21mm Mounts Tube Diameter = 30mm Mount System = 9.5 -11.5 mm dovetail Model T036C
£34.99
-
Sportsmatch Sportsmatch - 30mm Dovetail 9.5-11.5mm - TO35C - 15mm Mounts
Sportsmatch - 30mm Dovetail 9.5-11.5mm - TO35C - 15mm Mounts 30mm Diameter Body Tube - Medium 15mm ( A ) Mounts Tube Diameter = 30mm Mount System = 9.5 -11.5 mm dovetail With Arrestor Pin Model TO35C TO35C - SportsMatch Website
£38.99
-
Sportsmatch Sportsmatch - 30mm Picatinny / Weaver - T078 - 15mm Mounts
Sportsmatch - 30mm Picatinny / Weaver - T078 - 15mm Mounts Single Thumb Turn mount Fits 30mm tube For Scopes Upto 50mm 2 PIECE MEDIUM WEAVER / PICATINNY 30mm A = 15mm B = 21mm Weight = 108g Includes square section hardenedsteel arrestor bolt.
£64.99
-
Sportsmatch Sportsmatch - 34mm Dovetail 9.5-11.5mm - ATP34 - 21mm Mounts - Height Adjustable
Sportsmatch - 34mm Dovetail 9.5-11.5mm - ATP34 - 21mm Mounts - Height Adjustable Height Adjustable Tube Diameter = 34mm Mount System = 9.5 -11.5 mm dovetail Model ATP34 A = 24mm to 25.3mm saddle (Height from where the ring base touches rail to bottom of scope ring) Height varies due to elevation adjustment.B = 21mm longWeight = 133g Includes removable arrestor pin Adjustable for elevation and height. Upto 40 MOA Vertical Adjustment
£111.80
-
Sportsmatch Sportsmatch - 34mm Picatinny / Weaver - 13mm High - Medium
Sportsmatch - 34mm Picatinny / Weaver - 13mm High - Medium - T088 34mm Diameter Body Tube Medium Range Suitable for all Weaver / Picatinny rails. Includes square section hardened steel arrestor bolt. Up to 50mm lens diameter (on most rifles) 34mm Diameter Body Tube Tube Diameter = 34mm Mount System = Weaver / Picatinny Model T088 13mm Height ( A ) - From bottom of clamp to bottom of scope ring. B = 21mm long
£74.99
-
Sportsmatch Sportsmatch - 34mm Picatinny / Weaver - HT089 - 19mm High Mounts
Sportsmatch Scope Mount 34mm Picatinny HT089 - 19mm Single Thumb Turn mount Height Adjustable Tube Diameter = 34mm Mount System = 21mm Wide Base Picatinny / Weaver Model HT089 14mm - Saddle (Height from where the ring base touches rail to bottom of scope ring) 19mm - Bottom of mount to bottom of scope ( A ) 55mm - Overall height.Weight = 126g Includes removable arrestor pin Ideal for 56mm Scope
£89.99£81.99
-
Sportsmatch Sportsmatch SP3 Spirit Level 1" & 30mm Swing Out
Sportsmatch SP3 Spirit Level 1" & 30mm Swing Out Sportsmatch SP3 Spirit Level 1" & 30mm Swing Out Sold as single item This is for Sportsmatch Mounts.
£47.99
-
Sportsmatch Sportsmatch SP4 Spirit Level Side Mounted
Sportsmatch SP4 Spirit Level Side Mounted Weight 8g Fits all Sportsmatch mounts with M5 (larger) dovetail clamp screws. Visible without moving eye away from scope. YOU MUST BE USING SPORTSMATCH MOUNTS FOR THIS TO FIT. Not returnable if blister packing is opened.
£44.99£39.99
-
Saber Tactical Stainless Steel Extended Quick Disconnect - Foster Fitting M32
Stainless Steel Extended Quick Disconnect - Foster Fitting M32 This extended quick disconnect (QD) makes it easy for those guns with hard to reach fill nipples. A must have for FX Impacts. Male foster fitting Max 4500 psi (Do not exceed recommended pressure) Release collar close to 1.20 inches long This product attaches to your existing high pressure foster connecting. Caution you are using High Pressure Air. This is an aftermarket accessory designed for home fitting. We do not provide any fitting service. Airgun 101 Shop is in no way liable for any damage / harm / injury to any person or item when fitting or failure of this product.
£24.99
-
Jack Pyke Steel Target Airgun Pellet Catcher 14cm x 14cm
Steel Target Airgun Pellet Catcher 14cm x 14cm Includes 10 paper targets Paper target size 14cm x 14cm Designed for UK Sub 12 Ft Lb Airguns.
£9.95
-
Best Fittings Steyr LG Quick Fill Probe
Steyr LG Quick Fill Probe Suits Steyr LG rifles fitted with the Quick Fill Probe filling system. Standard 1/8″BSP male thread for direct fitting to a flexible fill line or our Quick Coupler Plugs. Complete with two spare O-rings and silicone grease kit. CAUTION - You are working with high pressure air, always be safe. Airgun 101 Shop is not responsible for any injury / damage to any person, third party or item when using this part.
£15.00
-
SupaTool SupaTool Driver Bits 33 Piece
SupaTool Driver Bits 33 Piece Cross Point: PH0, 2 x PH1, 2 x PH2, 2 x PH3 Slotted: 3mm, 4mm, 5mm, 6mm, 7mm Pozi: 2 x PZ1, 3 x PZ2, 2 x PZ3 Hex: 2mm, 2 5mm, 3mm, 4mm, 5mm, 6mm Torx T10, T15, T20, T25, T30, T40 1 pc 60mm Extension bar PVC organiser Sandblasted chrome vanadium steel bits NOT recommended for Impact Drivers, or high torque electric screwdrivers Only recommended for hand tool use.
£5.49
-
SupaTool SupaTool Socket Set - 40 Piece
SupaTool Socket Set 7" Reversible Ratchet Handle 3" Extension Bar 1/4" (M) x 3/8" (F) Adaptor Spin Disc 14 x 1/4" Dr SAE: 5/32", 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32",1/2", 17/32", 9/16" 14 x 1/4" Dr Metric:4, 4 5, 5, 5 5, 6, 6 5, 7, 7 5, 8, 9, 10, 11, 12 and 13mm 3/8" Dr Metric: 14mm 3 x 1/4" Dr (8pt) SAE: 1/4", 5/16", 3/8" 3 x Hex Key Wrench Plastic Case NOT recommended for Impact Drivers, or high torque electric screwdrivers Only recommended for hand tool use.
£14.99
-
Ergo Surestop Picatinny Tactical Hand Stop
Surestop Picatinny Tactical Hand Stop Give yourself another hand hold in seconds with the ERGO Air SURESTOP Tactical Hand Stop. Attaches securely to any Picatinny rail in seconds. ERGO Air SURESTOP Tactical Hand Stop in Black. Useful on short Airguns for additional control Can act as a hand positioning device Compatible with any picatinny rail system This is an add on grip, it's only as secure as the rail that you are adding too. This is a home install product, we are not responsible for any harm, injury air damage to any person or item when using or installing this product. Safety First.
£11.99
-
Victorinox Swiss Army knife - 7 Function - Classic - Black - Pen Knife
Swiss Army knife - 7 Function - Classic - Black - Pen Knife Victorinox pocket tools incorporate more than a century of tradition and experience. Nowadays, the "Swiss Army Knife" enjoys international protection and, more than any other product, stands for the world-famous "Swiss Made" label of quality. 1. Small blade 2. Scissors 3. Nail file with 4. Screwdriver 5. Tweezers 6. Toothpick Approx 6cm Long / 2 cm Wide - small lightweight. Over 18's ONLY Strictly In Store Collection and ID will be required. We DO NOT retail this item outside of the store in the UK. If you attempt to circumnavigate the in store collection policy we will refuse your custom. If you purchase and REFUSE to collect from store, we will deduct any merchant charges that have been applied to us.
£17.99£17.49
-
Victorinox Swiss Army knife - 7 Function - Classic - Red - Pen Knife
Swiss Army knife - 7 Function - Classic - Red - Pen Knife Victorinox pocket tools incorporate more than a century of tradition and experience. Nowadays, the "Swiss Army Knife" enjoys international protection and, more than any other product, stands for the world-famous "Swiss Made" label of quality. 1. Small blade 2. Scissors 3. Nail file with 4. Screwdriver 5. Tweezers 6. Toothpick Approx 6cm Long / 2 cm Wide - small lightweight. Over 18's ONLY Strictly In Store Collection and ID will be required. We DO NOT retail this item outside of the store in the UK. If you attempt to circumnavigate the in store collection policy we will refuse your custom. If you purchase and REFUSE to collect from store, we will deduct any merchant charges that have been applied to us.
£17.99£17.49
-
Sytong Nightvision Sytong HT-66 12mm 1-3.5x Digital Night Vision Rear Add On
Sytong HT-66 12mm 1-3.5x Digital Night Vision Rear Add On FACTORY SPECIAL OFFER - WHEN ITS GONE ITS GONE. New for 2021, the Sytong HT-66 1x-3.5x 12mm Night Vision Rear Add On allows you to quickly turn your standard optical Scope into a high-performance Night Vision system. Designed to fit the needs of both Air Rifle and Centerfire shooters. Offering a wider field of view (when compared to the 16mm counterpart due to slightly less magnification) the 12mm hits the needs of shooters who require their device for shorter ranges. The large internal screen produces a high resolution and clear image of your surroundings in full colour during daytime or switch to night mode and use three levels of 850nm IR intensity with the focusable lens system to generate a clear view over hundreds of meters during complete darkness. The supplied 45mm collar attaches to the eyepiece of your scope and allows you to quickly attach and detach the unit as the shooting conditions change, without any shift in point of impact. (Additional collars in various sizes will be available in due course.) This is an exciting and high-performing addition to the Night Vision Shooting Optics! The manufacturer includes a Power Adapter - however we advise to ONLY charge the 18650 battery using an external charger, any damage caused to the unit during charging is NOT covered by the warranty. Please note: TF Memory Card not included. Laser Pointer has been removed. Battery not included on orders outside of mainland UK (including Northern Ireland). A 3 Pin Plug Adapter is required. Not included. More Information Brand Sytong Popularity Sytong HT-66 12mm 1-3.5x Digital Night Vision Rear Add On SKU SYT-HT66-W-12MM-45MM Unit Type Night Vision Display Resolution 1024x768 Display Type AMOLED FOV @ 100 yards 21° Infrared Illuminator Wavelength 850nm Magnification (Optical) 3.5x Operating Temperature -20/+50°C Sensor Resolution 1920x1080 Video Recording Yes WiFi Yes Sony CMOS sensor, the new sensor offers the following advantages over the Pard NV007A Clearer image compared to the Pard 007A giving a greater viewing range. No picture lag when panning. The Sytong can still be used where you can no longer see anything with the Pard without an IR emitter. The sensor can down-regulate the image much faster when the IR light is switched on. No more fading due to overly focusable IR light, this means using in an enclosed area such as a forest is much easier on the eye. The screen can be dimmed down to 10% at the push of a button, from “extra dark” to “extra bright”. (With Pard this is only possible via the menu and only up to 50%). Integrated gyrometer sensor with rotation and inclination angle display. All buttons can be operated silently. The IR emitter can be focused more strongly, which also increases the range. According to the manufacturer, the device is bulletproof up to 6000 joules, tested with caliber 9.3×62 mm (Pard up to 5000 J). Own app for live image transmission with direct access to previously saved photos and videos that can be downloaded directly to the smartphone. Better placed buttons simplify operation, especially in manual mode. SD card is much easier to change. Whats In the Box? Hex Wrench Sytong HT66 12mm Digital Night Vision Rear Add On Tape Data Cable 2 Pin Power Adapter (A 3 Pin UK Power Plug Adapter is required for use in the UK Not Included.) User Manual 1 x 18650 Battery Please note: TF Memory Card not included.
£259.95
-
Sytong Nightvision Sytong HT60 LRF 3-8x Digital Night Vision Rifle Scope (with Laser Rangefinder)
Sytong HT60 LRF 3-8x Digital Night Vision Rifle Scope (with Laser Rangefinder) FEATURES Integral laser rangefinder The perfectly designed Sytong HT60 now comes with an integral laser rangefinder, allowing shooters to laser rangefind their quarry to ensure they are accurately range finding when out in the field. Making their night shooting activities more accurate then ever. Environmental adaptability Waterproof grade IPX7, high-grade aviation aluminum alloy shell, fall and shock-resistant, strong and durable, high-temperature resistant, cold resistant and dust resistant. Far observation distance Max. magnification up to 8x.Max. Viewer distance up to 200m.Continuous zoom in and out.Infrared light synchronised with lens with clearer night vision effect. High imaging quality The display screen fulfills military-grade quality standards and its resolution, display effect, definition and colour are all industry-leading, which can greatly improve the observation experience, as well as manual support, mobile detection, and video recording. Simple operation, high capacity battery The HT-60 can be detached and used independently as a Night Vision Monocular. Wireless transmission, convenient storage, and up to 8 hours of battery life are added bonuses. The latest incarnation of the Sytong HT-60 LRF has arrived! The 3-8x has been created to fit the needs of the shooters who require less magnification and more Field of View. The versatile 3x magnification will make this a perfect choice for shooters looking to use the HT60 for vermin control at short range on Air Rifles, Rimfires and even Centerfires. This Digital Night Vision Rifle Scope now comes with an integral Laser Rangefinder ensuring you can make the most accurate decision before taking on targets. This small, compact and versatile Digital Night Vision Scope has the ability to be used as both a handheld Night vision LRF Monocular and also as one of the most affordable Laser Rangefinding Rifle Scopes on the market. The Sytong HT60 LRF offers a full-colour Scope for daytime shooting and switches seamlessly into a powerful Night Vision Scope at the press of a button. The large internal screen produces a high resolution and clear image of your surroundings, whilst the 3x base magnification, which can be boosted up to 8x with digital magnification, allows you to identify and engage with targets at longer distances. The onboard 850nm IR illuminator offers three intensity settings and can be focused to optimise the performance at close range or over long distances. The supplied Picatinny rail easily attaches the HT-60 LRF to your Gun and the zero menu is quick and easy to use. Please note: TF Memory Card not included. Laser Pointer has been removed. Battery not included on orders outside of mainland UK (including Northern Ireland). We do advise an external charger to charge the battery - do not charge the battery in the unit - 18650 batteries are high power and if the battery fails on charge it would damage the unit and this is not covered by the warranty. We give as a free gift an external charger with this unit. Non returnable and no cash value on the free charger. Adjustable Eaglevision mounts do not fit direct to the underside of this unit, the Sytong mounting bracket must still be used - but can be mounted onto an adjustable mount. More Information Manufacturer - Sytong Sytong HT60 LRF 3-8x Digital Night Vision Rifle Scope (with Laser Rangefinder) SYT-HT6038LRF Type - Night Vision Detection Range - 200m Display Resolution - 1024x768 Display Type - AMOLED FOV @ 100 Yards - 4.4° Generation - Digital Intergrated IR Illuminator - Yes IR Illuminator Wavelength - 850nm Magnification Digital - 2.66x Magnification Optical - 3x Operating Temp — 20/+50°C Rangefinder - LRF Sensor Resolution - 1920x1080 Video Recording - Yes Wifi - Yes SPECSHT60/LRF3 Type CMOSResolution, pixels 1920x1080Optical characteristics Objective lens focus 45mmMagnification 3/4/5/6/7/8xFocal ratio, D/f' 1:3Eye relief 40 mmFiled of view 6.0°X4.5°Diopter eyepiece adjustment +5/-5 DMin. focusing range 3mIR Illuminator YesType / Wavelength, nm 850Display Type / Resolution 0.39 inch / AMOLED / 1024X768Operational characteristics Power supply 3-4.2 VBattery 18650 /3200mAhExternal power supply 5V (USB)Operating time (at t=22℃) 6 hoursMax. recoil power, Joules 6000Degree of protection IP67Operating temperature ﹣20℃...50℃Dimensions 185X99X50 mmNet weight 490gVideo recorder Video / photo resolution 1024x768Video / photo format .mp4 / .jpgMemoery type TF card, max.support 128GWiFi YesWiFi Password 12345678Standart 802.11 b/gLine-of-sight reception range 15mLaser Rangefinder IntegralWavelength 905nmMax. measuring range 1000mMeasuring accuracy +/- 1m IN THE BOX? Sytong HT-60 LRF 3-8x Digital Night Vision Rifle Scope Picatinny Mount Data Cable Hex Wrench User Manual Cleaning Cloth 1 x 18650 Battery Please note: TF Memory Card not included. WE DO NOT SHIP THIS PRODUCT OUTSIDE OF ENGLAND, SCOTLAND AND WALES.
£739.99
-
Viper Tactical Tactical Handcuff Key
Tactical Handcuff Key Compatible with most handcuffs Length: 8cm
£4.99
-
GR8Fun Target Spinner + Target Holder - Red Set - GR8Fun
Target Spinner + Target Holder - Red Set - GR8Fun This is a pole, with a triangle ground spike on the bottom, plus spinners and a paper target holder. Very popular at clubs and for home shooters. The paper target frame at the top, in our experience can be a little wonky as it has to stick up unsupported - but if you ignore that its a great target. 16cm is the width of the target holder - thus conventional 14cm targets will require you to add a bit of extra cardboard backing. Some home assembly is required and 13mm spanner will be needed ( not supplied ) Overall heigh approx 73cm Bit above the spike is 59cm Suitable for rifles up to 12 FT Lbs. They also have a snooker version which can be found here.
£46.99
-
GR8Fun Target Spinner + Target Holder - Snooker Set - GR8Fun
Target Spinner + Target Holder - Snooker Set - GR8Fun This is a pole, with a triangle ground spike on the bottom, plus spinners and a paper target holder. Very popular at clubs and for home shooters. The paper target frame at the top, in our experience can be a little wonky as it has to stick up unsupported - but if you ignore that its a great target. 16cm is the width of the target holder - thus conventional 14cm targets will require you to add a bit of extra cardboard backing. Some home assembly is required and 13mm spanner will be needed ( not supplied ) Overall heigh approx 73cm Bit above the spike is 59cm Suitable for rifles up to 12 FT Lbs. They also have a Red Spinner version which can be found here.
£46.99
-
Jack Pyke Thinsulate Bob Hat - Black
Thinsulate Bob Hat - Black One size fits all. Originating from early 1900s the traditional beanie hat never goes out of fashion. The Jack Pyke Bob Hat is easy to fold and store in your pocket. Made of 100% Acrylic with Thinsulate lining the hat is as warm as it is practical. Classic design Material: 100% Acrylic Thinsulate lining
£3.49
-
Tier One Tier One - Scope Mounts 1 Inch 25.4mm Picatinny Medium
Tier One - Scope Mounts 25.4mm Picatinny Medium These are 1 Inch Mounts. Tier One makes some of the best scope rings on the market, high quality with a super high finish to them, made from a single piece of aluminium so you know the rings are true. Ships in a plastic box, with 2 x heads for the screws. Tier One Picatinny Rings are precision made on 5 axis CNC machinery. All sets come with one mount with a bubble level installed ( not both ) The key to accuracy in manufacture is to minimise the number of operations required to complete the machining process. By investing in new Technology, we have been able to cut the number of operations required from eight to two. By doing this, there is no accuracy loss due to re setting for different operations. All Rings are made from solid billets of Aluminium 7075T6 alloy and are available in medium and high configurations. Ring sizes from 1" up to 40mm Picatinny Rings available. Due to the precision of the manufacturing process, lapping is not required when mounted on a quality picatinny rail. Screws are stainless steel and manufactured by us on our own machines to the highest possible specification. WHAT CALIBERS ARE THESE RINGS FOR? We recommend torquing these rings to 18in/lbs because some scope manufacturers make their scopes from soft materials. Torquing any higher could cause marking or other damage to the scope tube. If you're torquing these rings to 18in/lbs then we don't recommend using them with magnum calibers. For magnum caliber rifles we highly recommend our one-piece mounting system, the Monomount. Or, the Tactical Rings, which are based on the Short Saddle mono but come in a two-piece format. Both have a much larger scope contact area. CAN I OVERTORQUE THE TOP RINGS? If you are happy that your scope is manufactured from a strong enough material to resist the extra pressure then you can, entirely at your own risk, torque them up to 26in/lbs as we do when using them on Magnum caliber rifles. IMPORTANT: You MUST check with your scope manufacturer before you do this and we take no responsibility if you mark or otherwise damage your scope tube. Tier One - From the Manufacturer Picatinny Ringset Mounting Instructions Our Picatinny Ringsets are manufactured to the highest tolerances, and it is advised to mount them on a suitable quality picatinny rail to get the optimum result. It is the purchaser’s decision to mount the picatinny rings and optic if they feel competent themselves, or seek advice from their favoured gunsmith. Place your unloaded firearm on a stable work surface, preferably mounted in a suitable gun vice. If no gun vice is available, the firearms own bipod can be utilised instead. It is now important to ascertain the correct eye relief. First loosen the clamp screws with the T25 Torx bit supplied to allow loose placement upon the picatinny rail, now remove the ring cap screws using the supplied T15 Torx bit, and gently attach the rings onto your picatinny rail, lightly tightening at this stage, ensuring the rear most one does not foul on the firearms bolt when worked. You now have a starting point to set your correct optic position. Place the optic into the rings and shoulder your firearm carefully, you may want to replace the ring caps very loosely to avoid letting your optic fall out of the mounts whilst doing this. As a guide, it is generally better if the rings are as far apart as possible to gain maximum strength and stability. Your optic should be set at the maximum magnification and if present, the parallax correction set to infinity. When viewing your optic from the shouldered position you should be able to see a clear image. If you can see a dark ring around the ocular lens gently move your optic fore or aft until this disappears. Great care should be taken at this point not to damage your optics finish. A pencil mark placed upon the optic as reference to the ring cap location will aid the final stage of mounting. You have now set the correct position for the ringset bases. Remove the ring caps and optic and tighten the T25 Torx screw on the ring claw to 4Nm, ensuring the ring bases are pushed firmly toward the muzzle to counter the effects of recoil. Now place your optic back into the rings using your pencil datum points as a guide, replace the ring caps, and using the T15 Torx bit in your fingers only, tighten the screws gently and evenly to maintain an equal gap between ring base and cap. Only light pressure is needed as it is important at this stage to be able to turn the optic in the rings without damage occurring to the finish. It is the installer’s decision to mount the optic by utilising the bubble built into the rear ring to level the rifle, and also a separate bubble placed upon the optics elevation turret cap, or by shouldering their firearm whilst viewing a suitable true vertical line, and rotating the optic gently until the bubble levels align, or the reticle matches the chosen vertical line. Care should again be taken at this stage to ensure no damage occurs to the optics outer finish. Once the installer is happy with the reticle alignment, the ring cap screws should be tightened gently and evenly, at opposing corners, whilst maintaining an equal gap to both sides, up to the recommended torque setting of 2Nm. Care at this stage should be taken to ensure your optic remains level, and doesn’t move during the tightening process.
£145.99£129.99
-
Tier One Tier One - Scope Mounts 30mm Picatinny High
Tier One - Scope Mounts 30mm Picatinny High These are 30mm Mounts. Tier One makes some of the best scope rings on the market, high quality with a super high finish to them, made from a single piece of aluminium so you know the rings are true. Ships in a box, with 2 x heads for the screws. Tier One Picatinny Rings are precision made on 5 axis CNC machinery. All sets come with one mount with a bubble level installed ( not both ) The key to accuracy in manufacture is to minimise the number of operations required to complete the machining process. By investing in new Technology, we have been able to cut the number of operations required from eight to two. By doing this, there is no accuracy loss due to re setting for different operations. All Rings are made from solid billets of Aluminium 7075T6 alloy and are available in medium and high configurations. Ring sizes from 1" up to 40mm Picatinny Rings available. Due to the precision of the manufacturing process, lapping is not required when mounted on a quality picatinny rail. Screws are stainless steel and manufactured by us on our own machines to the highest possible specification. WHAT CALIBERS ARE THESE RINGS FOR? We recommend torquing these rings to 18in/lbs because some scope manufacturers make their scopes from soft materials. Torquing any higher could cause marking or other damage to the scope tube. If you're torquing these rings to 18in/lbs then we don't recommend using them with magnum calibers. For magnum caliber rifles we highly recommend our one-piece mounting system, the Monomount. Or, the Tactical Rings, which are based on the Short Saddle mono but come in a two-piece format. Both have a much larger scope contact area. CAN I OVERTORQUE THE TOP RINGS? If you are happy that your scope is manufactured from a strong enough material to resist the extra pressure then you can, entirely at your own risk, torque them up to 26in/lbs as we do when using them on Magnum caliber rifles. IMPORTANT: You MUST check with your scope manufacturer before you do this and we take no responsibility if you mark or otherwise damage your scope tube. Tier One - From the Manufacturer Picatinny Ringset Mounting Instructions Our Picatinny Ringsets are manufactured to the highest tolerances, and it is advised to mount them on a suitable quality picatinny rail to get the optimum result. It is the purchaser’s decision to mount the picatinny rings and optic if they feel competent themselves, or seek advice from their favoured gunsmith. Place your unloaded firearm on a stable work surface, preferably mounted in a suitable gun vice. If no gun vice is available, the firearms own bipod can be utilised instead. It is now important to ascertain the correct eye relief. First loosen the clamp screws with the T25 Torx bit supplied to allow loose placement upon the picatinny rail, now remove the ring cap screws using the supplied T15 Torx bit, and gently attach the rings onto your picatinny rail, lightly tightening at this stage, ensuring the rear most one does not foul on the firearms bolt when worked. You now have a starting point to set your correct optic position. Place the optic into the rings and shoulder your firearm carefully, you may want to replace the ring caps very loosely to avoid letting your optic fall out of the mounts whilst doing this. As a guide, it is generally better if the rings are as far apart as possible to gain maximum strength and stability. Your optic should be set at the maximum magnification and if present, the parallax correction set to infinity. When viewing your optic from the shouldered position you should be able to see a clear image. If you can see a dark ring around the ocular lens gently move your optic fore or aft until this disappears. Great care should be taken at this point not to damage your optics finish. A pencil mark placed upon the optic as reference to the ring cap location will aid the final stage of mounting. You have now set the correct position for the ringset bases. Remove the ring caps and optic and tighten the T25 Torx screw on the ring claw to 4Nm, ensuring the ring bases are pushed firmly toward the muzzle to counter the effects of recoil. Now place your optic back into the rings using your pencil datum points as a guide, replace the ring caps, and using the T15 Torx bit in your fingers only, tighten the screws gently and evenly to maintain an equal gap between ring base and cap. Only light pressure is needed as it is important at this stage to be able to turn the optic in the rings without damage occurring to the finish. It is the installer’s decision to mount the optic by utilising the bubble built into the rear ring to level the rifle, and also a separate bubble placed upon the optics elevation turret cap, or by shouldering their firearm whilst viewing a suitable true vertical line, and rotating the optic gently until the bubble levels align, or the reticle matches the chosen vertical line. Care should again be taken at this stage to ensure no damage occurs to the optics outer finish. Once the installer is happy with the reticle alignment, the ring cap screws should be tightened gently and evenly, at opposing corners, whilst maintaining an equal gap to both sides, up to the recommended torque setting of 2Nm. Care at this stage should be taken to ensure your optic remains level, and doesn’t move during the tightening process.
£145.99£124.99
-
Tier One Tier One - Scope Mounts 30mm Picatinny Low
Tier One - Scope Mounts 30mm Picatinny Low These are 30mm Mounts. Tier One makes some of the best scope rings on the market, high quality with a super high finish to them, made from a single piece of aluminium so you know the rings are true. Ships in a display box, with 2 x heads for the screws. Tier One Picatinny Rings are precision made on 5 axis CNC machinery. All sets come with one mount with a bubble level installed ( not both ) The key to accuracy in manufacture is to minimise the number of operations required to complete the machining process. By investing in new Technology, we have been able to cut the number of operations required from eight to two. By doing this, there is no accuracy loss due to re setting for different operations. All Rings are made from solid billets of Aluminium 7075T6 alloy and are available in medium and high configurations. Ring sizes from 1" up to 40mm Picatinny Rings available. Due to the precision of the manufacturing process, lapping is not required when mounted on a quality picatinny rail. Screws are stainless steel and manufactured by us on our own machines to the highest possible specification. Low Mounts 30mm Picatinny Measurement A = 22mm WHAT CALIBERS ARE THESE RINGS FOR? We recommend torquing these rings to 18in/lbs because some scope manufacturers make their scopes from soft materials. Torquing any higher could cause marking or other damage to the scope tube. If you're torquing these rings to 18in/lbs then we don't recommend using them with magnum calibers. For magnum caliber rifles we highly recommend our one-piece mounting system, the Monomount. Or, the Tactical Rings, which are based on the Short Saddle mono but come in a two-piece format. Both have a much larger scope contact area. CAN I OVERTORQUE THE TOP RINGS? If you are happy that your scope is manufactured from a strong enough material to resist the extra pressure then you can, entirely at your own risk, torque them up to 26in/lbs as we do when using them on Magnum caliber rifles. IMPORTANT: You MUST check with your scope manufacturer before you do this and we take no responsibility if you mark or otherwise damage your scope tube. Tier One - From the Manufacturer Picatinny Ringset Mounting Instructions Our Picatinny Ringsets are manufactured to the highest tolerances, and it is advised to mount them on a suitable quality picatinny rail to get the optimum result. It is the purchaser’s decision to mount the picatinny rings and optic if they feel competent themselves, or seek advice from their favoured gunsmith. Place your unloaded firearm on a stable work surface, preferably mounted in a suitable gun vice. If no gun vice is available, the firearms own bipod can be utilised instead. It is now important to ascertain the correct eye relief. First loosen the clamp screws with the T25 Torx bit supplied to allow loose placement upon the picatinny rail, now remove the ring cap screws using the supplied T15 Torx bit, and gently attach the rings onto your picatinny rail, lightly tightening at this stage, ensuring the rear most one does not foul on the firearms bolt when worked. You now have a starting point to set your correct optic position. Place the optic into the rings and shoulder your firearm carefully, you may want to replace the ring caps very loosely to avoid letting your optic fall out of the mounts whilst doing this. As a guide, it is generally better if the rings are as far apart as possible to gain maximum strength and stability. Your optic should be set at the maximum magnification and if present, the parallax correction set to infinity. When viewing your optic from the shouldered position you should be able to see a clear image. If you can see a dark ring around the ocular lens gently move your optic fore or aft until this disappears. Great care should be taken at this point not to damage your optics finish. A pencil mark placed upon the optic as reference to the ring cap location will aid the final stage of mounting. You have now set the correct position for the ringset bases. Remove the ring caps and optic and tighten the T25 Torx screw on the ring claw to 4Nm, ensuring the ring bases are pushed firmly toward the muzzle to counter the effects of recoil. Now place your optic back into the rings using your pencil datum points as a guide, replace the ring caps, and using the T15 Torx bit in your fingers only, tighten the screws gently and evenly to maintain an equal gap between ring base and cap. Only light pressure is needed as it is important at this stage to be able to turn the optic in the rings without damage occurring to the finish. It is the installer’s decision to mount the optic by utilising the bubble built into the rear ring to level the rifle, and also a separate bubble placed upon the optics elevation turret cap, or by shouldering their firearm whilst viewing a suitable true vertical line, and rotating the optic gently until the bubble levels align, or the reticle matches the chosen vertical line. Care should again be taken at this stage to ensure no damage occurs to the optics outer finish. Once the installer is happy with the reticle alignment, the ring cap screws should be tightened gently and evenly, at opposing corners, whilst maintaining an equal gap to both sides, up to the recommended torque setting of 2Nm. Care at this stage should be taken to ensure your optic remains level, and doesn’t move during the tightening process.
£145.99£129.99
-
Tier One Tier One - Scope Mounts 30mm Picatinny Medium
Tier One - Scope Mounts 30mm Picatinny Medium These are 30mm Mounts. Tier One makes some of the best scope rings on the market, high quality with a super high finish to them, made from a single piece of aluminium so you know the rings are true. Ships in a box, with 2 x heads for the screws. Tier One Picatinny Rings are precision made on 5 axis CNC machinery. All sets come with one mount with a bubble level installed ( not both ) The key to accuracy in manufacture is to minimise the number of operations required to complete the machining process. By investing in new Technology, we have been able to cut the number of operations required from eight to two. By doing this, there is no accuracy loss due to re setting for different operations. All Rings are made from solid billets of Aluminium 7075T6 alloy and are available in medium and high configurations. Ring sizes from 1" up to 40mm Picatinny Rings available. Due to the precision of the manufacturing process, lapping is not required when mounted on a quality picatinny rail. Screws are stainless steel and manufactured by us on our own machines to the highest possible specification. WHAT CALIBERS ARE THESE RINGS FOR? We recommend torquing these rings to 18in/lbs because some scope manufacturers make their scopes from soft materials. Torquing any higher could cause marking or other damage to the scope tube. If you're torquing these rings to 18in/lbs then we don't recommend using them with magnum calibers. For magnum caliber rifles we highly recommend our one-piece mounting system, the Monomount. Or, the Tactical Rings, which are based on the Short Saddle mono but come in a two-piece format. Both have a much larger scope contact area. CAN I OVERTORQUE THE TOP RINGS? If you are happy that your scope is manufactured from a strong enough material to resist the extra pressure then you can, entirely at your own risk, torque them up to 26in/lbs as we do when using them on Magnum caliber rifles. IMPORTANT: You MUST check with your scope manufacturer before you do this and we take no responsibility if you mark or otherwise damage your scope tube. Tier One - From the Manufacturer Picatinny Ringset Mounting Instructions Our Picatinny Ringsets are manufactured to the highest tolerances, and it is advised to mount them on a suitable quality picatinny rail to get the optimum result. It is the purchaser’s decision to mount the picatinny rings and optic if they feel competent themselves, or seek advice from their favoured gunsmith. Place your unloaded firearm on a stable work surface, preferably mounted in a suitable gun vice. If no gun vice is available, the firearms own bipod can be utilised instead. It is now important to ascertain the correct eye relief. First loosen the clamp screws with the T25 Torx bit supplied to allow loose placement upon the picatinny rail, now remove the ring cap screws using the supplied T15 Torx bit, and gently attach the rings onto your picatinny rail, lightly tightening at this stage, ensuring the rear most one does not foul on the firearms bolt when worked. You now have a starting point to set your correct optic position. Place the optic into the rings and shoulder your firearm carefully, you may want to replace the ring caps very loosely to avoid letting your optic fall out of the mounts whilst doing this. As a guide, it is generally better if the rings are as far apart as possible to gain maximum strength and stability. Your optic should be set at the maximum magnification and if present, the parallax correction set to infinity. When viewing your optic from the shouldered position you should be able to see a clear image. If you can see a dark ring around the ocular lens gently move your optic fore or aft until this disappears. Great care should be taken at this point not to damage your optics finish. A pencil mark placed upon the optic as reference to the ring cap location will aid the final stage of mounting. You have now set the correct position for the ringset bases. Remove the ring caps and optic and tighten the T25 Torx screw on the ring claw to 4Nm, ensuring the ring bases are pushed firmly toward the muzzle to counter the effects of recoil. Now place your optic back into the rings using your pencil datum points as a guide, replace the ring caps, and using the T15 Torx bit in your fingers only, tighten the screws gently and evenly to maintain an equal gap between ring base and cap. Only light pressure is needed as it is important at this stage to be able to turn the optic in the rings without damage occurring to the finish. It is the installer’s decision to mount the optic by utilising the bubble built into the rear ring to level the rifle, and also a separate bubble placed upon the optics elevation turret cap, or by shouldering their firearm whilst viewing a suitable true vertical line, and rotating the optic gently until the bubble levels align, or the reticle matches the chosen vertical line. Care should again be taken at this stage to ensure no damage occurs to the optics outer finish. Once the installer is happy with the reticle alignment, the ring cap screws should be tightened gently and evenly, at opposing corners, whilst maintaining an equal gap to both sides, up to the recommended torque setting of 2Nm. Care at this stage should be taken to ensure your optic remains level, and doesn’t move during the tightening process.
£145.99£124.99
-
Sportsmatch Tikka/CZ/Brno Adaptors Pair Converts Rails 15-9.5mm RB4
Tikka/CZ/Brno Adaptors Pair Converts Rails 15-9.5mm RB4 15mm - 9.5mm dovetail adapter rail allows any of our air rifle / rimfire mounts to be fitted to Tikka, CZ527 and early Brno .22 rifle SOLD AS A PAIR.
£34.99
-
Umarex Umarex - K3 Neo Airgun Silencer by Umarex (UMK3N) 1/2x20Unf
Umarex - K3 Neo Airgun Silencer by Umarex (UMK3N) 1/2x20Unf 1.5” DIAMETER x 5.5" LENGTH The Umarex 3- chamber silencer suppresses the muzzle sound significantly. This silencer is made of high-quality aluminium and is ideal for all airguns .177 and .22. 1/2" UNF thread. New matt finish and tapered end for an upgraded look. This is a single sized moderator can be used for .177 or .22. it's not dedicated for either caliber. So if your looking for a dedicated .177 or .22 mod then this is not for you. It is a tight bore for .22, so if you have any clipping check the alignment of your barrel. This silencer / moderator is for Unlicensed Airguns only. We are not responsible for clipping or any misalignment of your barrel. If the moderator is fitted and or used / damaged in any way it is not returnable. We do not ship this item outside of the UK You must be over 18 to purchase this item as declared on entry to the site.
£48.99
-
Umarex Umarex - Combat Zone Clear Shooting Safety Glasses
Umarex - Combat Zone Clear Shooting Safety Glasses These are clear CE marked safety glasses for shooting. Ideal to help prevent eye damage from powder sparks, cartridges and BB's that may bounce.They are made of plastic and are not bulletproof or designed to take a direct hit from any fired projectile. Use of these does not provide 100% protection.
£10.95£8.95
-
Umarex Umarex - Metal Shells Pack of 10 - Pellet - For Legends Range - Silver
Metal Shells Pack of 10 - Pellet - For Legends Range - Silver Colour Replacement / Spare shells for the Legends Cowboy Rifle / CO2 Pistols Replacement / Spare shells for the Colt Single Action Army Replica Pistol. For Pellet Version Rifle NOT included.
£23.00
-
Umarex Umarex - Steel BB Ammo - 1500 per Bottle 4.5mm .177cal
Umarex - Steel BB Ammo - 1500 per Bottle 4.5mm .177cal Top quality Steel BB's from Umarex of Germany Great value 1500 pack of steel BB's - will only suit airguns that are designed to shoot steel BB's (not soft air). These precision made BB's are manufactured to the highest standards of finish and consistency. Umarex .177 Steel BB's - 1500 Pack. Calibre: .177 (4.4mm) Steel BB's Quantity Supplied: 1500 Weight: 5.6 Grains IMPORTANT Info: These BB's are not plastic and will ONLY WORK in airguns designed for steel BB's. Not for Soft Air 18 + UK Law - You MUST be over 18 years old to purchase - if you purchase you are legally declaring you are over 18 years old. Full Checkout Terms and Explanation of this can be found HERE
£5.99
-
Umarex Umarex - Steel BB Ammo - 5000 per Bottle 4.5mm .177cal
Umarex - Steel BB Ammo - 5000 per Bottle 4.5mm .177cal Top quality Steel BB's from Umarex of Germany Great value 5000 pack of steel BB's - will only suit airguns that are designed to shoot steel BB's (not soft air). These precision made BB's are manufactured to the highest standards of finish and consistency. Umarex .177 Steel BB's - 1500 Pack. Calibre: .177 (4.4mm) Steel BB's Quantity Supplied: 5000 Weight: 5.6 Grains IMPORTANT Info: These BB's are not plastic and will ONLY WORK in airguns designed for steel BB's. Not for Soft Air 18 + UK Law - You MUST be over 18 years old to purchase - if you purchase you are legally declaring you are over 18 years old. Full Checkout Terms and Explanation of this can be found HERE
£22.99£21.39
-
Umarex Umarex / Walther Nano Laser Micro Shot NL3
Umarex / Walther Nano Laser Micro Shot NL3 Rail mount laser sight (650 nm), for Picatinny rail Batteries included. TECHNICAL DATA Laser class 2 / < 1 mW (EN 60825-1:2014/AC:2017) Wavelength 650 nm Mount Picatinny Length 45 mm Weight 28 g This is a Class 2 Laser. Do not look at the beam, do not point at aircraft.
£39.99£36.99
-
Umarex Umarex / Walther RDS6 Red Dot Sight
Umarex / Walther RDS6 Red Dot Sight A sturdy, closed dot sight with optionally green or red dot. Five levels of brightness each color for every light condition around and at the target. With integrated mount for Picatinny rails. TECHNICAL DATA Brightness levels 5 Illumination red / green Dot size (MOA) 6 Parallax adjusted to 10 m Mount Picatinny Length 66 mm Weight 120 g
£79.99£73.99
-
Umarex Umarex Combat Zone Airsoft 6mm BB 0.12g - 2700 Orange
Umarex Combat Zone Airsoft 6mm BB 0.12g - 2700 Orange High quality BB's for Airsoft. 2700 approx per bottle. 6mm 0.12g
£5.99
-
Umarex Umarex Elite Force Airsoft 6mm BB 0.3g - 2700 White
Umarex Elite Force Airsoft 6mm BB 0.3g - 2700 White High quality BB's for Airsoft. 2700 approx per bottle. 6mm 0.3g
£18.99
-
Umarex Umarex Green Dot Sight - Weaver Rail
Umarex Green Dot Sight - Weaver Rail Green dot with two brightness levels and 10 MOA. Dot sight for Picatinny rail Parallax adjusted to 25 m Color of dot: green Lateral battery compartment Incl. battery (CR 2032) TECHNICAL DATA Brightness levels 2 Illumination green Dot size (MOA) 10 Parallax adjusted to 25 m Recoil resistance .22 lr Length 80 mm Weight 58 g Requires 1 x CR2032 battery included.
£69.99£49.99
-
Umarex Umarex NP3 - Nano Point 3 - Red / Green Dot Sight
Umarex NP3 - Nano Point 3 Nano Point 3 Compact and lightweight Point Sight Power supply via battery CR2032 (included) Incl. Picatinny mount TECHNICAL DATA Brightness levels 1 Illumination red / green Dot size (MOA) 6 Parallax adjusted to 10 m Recoil resistance .22 lr Length 48 mm Weight 56 g
£64.99£44.49
-
Umarex Umarex Pellet Trap - Duck Hunter
Umarex Pellet Trap - Duck Hunter This rugged pellet trap made of sheet steel provides hours of reliable service – safe shooting for young and old. Pellet trap, black, with four steel duck silhouettes. When the smaller center target is hit all targets return to the upright position. Suitable for pellets up to 7.5 Joules / 6ft Lbs However if your rifle is a full Sub 12 Ft Lb - you can still use it, just put the target out 35m away, the pellet speed will drop enough to not be too damaging to the target. The targets stay down using magnets, it has to be a clean good hit....its magnets you have to allow for sometimes the laws of magnetism not working. TECHNICAL DATA suitable for < 7.5 J Usage stand-alone, top mount, wall mount Material steel Dimensions (mm) 500 x 225 x 200 Weight 5200 g Sub 12 Ft Lb air rifles will damage this target - thus it's your error if you shoot it with something too powerful too close. Also - its designed to be shot at, it will get damaged when being shot at - so we don't repair them or warranty them if they have been shot at...so a little home DIY may be needed to keep it running long term.
£39.99£34.95
-
Umarex Umarex Rail Mount Laser for Picatinny
Umarex Rail Mount Laser for Picatinny Rail mount laser for weaver rails. Use this laser for the underneath of your pistol. The mount also has another weaver rail beneath it to fit a flashlight. Class 2 laser, 650nm Logo's may vary on the product. • laser class 2 for mounting on guns • wavelength 650 nm • weight 31 g, length 36 mm • batteries included (4 x LR41) TECHNICAL DATA Laser class 2 / < 1 mW (EN 60825-1:2014/AC:2017) Wavelength 650 nm Mount Picatinny Length 36 mm Weight 31 g This is a Class 2 Laser. Do not look at the beam, do not point at aircraft. <1mW - 650nm EN60825-1-2014
£33.71
You have seen 816 out of 927 products